Difference between revisions of "3D Print Problems"
| Line 1: | Line 1: | ||
https://www.simplify3d.com/support/print-quality-troubleshooting/ | https://www.simplify3d.com/support/print-quality-troubleshooting/ | ||
| − | = | + | = Print Aborted = |
| − | + | == Running out of filament == | |
| − | + | The amount of initial filiament shipped with my {{Link|target=Geeetech_A10}} was simply not enough to finish the print job: | |
| − | + | [[File:Dog_Abouted2_IMG_2762.JPG|400px]] | |
| − | + | ||
| − | [[ | + | == Rebooting computer while USB is connected == |
| + | When installing a new USB driver the computer rebooted - it's probably the same if you unplug and plug the USB cable while printing from SD card: | ||
| + | |||
| + | [[File:Dog_Aborted1_IMG_2761.JPG|400px]] | ||
| + | |||
= Undextrusion = | = Undextrusion = | ||
See e.g. | See e.g. | ||
| Line 27: | Line 31: | ||
= Changing filament = | = Changing filament = | ||
* [https://www.youtube.com/watch?v=Od3W-asW3FY Change Filament] | * [https://www.youtube.com/watch?v=Od3W-asW3FY Change Filament] | ||
| − | + | = Pillowing = | |
| + | <youtube>CKJE92bfu0o</youtube> | ||
| + | * https://all3dp.com/2/3d-printing-top-layer-problems-easy-fixes-for-pillowing/ | ||
| + | * https://rigid.ink/blogs/news/pillowing-stringing-and-splitting-what-they-are-and-how-to-stop-them | ||
| + | * https://www.raise3d.com/pages/holes-and-gaps-in-solid-layers | ||
| + | [[Category:3DPrint]] | ||
= Speed = | = Speed = | ||
== Experiments with a small test cube == | == Experiments with a small test cube == | ||
Revision as of 19:38, 19 February 2019
https://www.simplify3d.com/support/print-quality-troubleshooting/
Print Aborted
Running out of filament
The amount of initial filiament shipped with my Geeetech_A10 was simply not enough to finish the print job:
Rebooting computer while USB is connected
When installing a new USB driver the computer rebooted - it's probably the same if you unplug and plug the USB cable while printing from SD card:
Undextrusion
See e.g.
- https://www.raise3d.com/pages/extruding-too-little-much-plastic
- https://ultimaker.com/en/resources/21477-how-to-fix-under-extrusion
in my case it happened when I set the Filament settings in the marlin menu with
"E in mm3" to 1.75. This was a misunderstanding that lead the software to assume my filament was flowing faster than it was. After switching the volumentric value off things were much better.
Clogged Nozzle
See e.g.
Print stuck to glass / print bed
I had best results with the temperature method in combination with taping the bed before printing. With a minus 17 degree cooling pad from the deep fridge below the glas bed and a gentle stroke with the rubber hammer the problem usually went away within a minute.
Changing filament
Pillowing
- https://all3dp.com/2/3d-printing-top-layer-problems-easy-fixes-for-pillowing/
- https://rigid.ink/blogs/news/pillowing-stringing-and-splitting-what-they-are-and-how-to-stop-them
- https://www.raise3d.com/pages/holes-and-gaps-in-solid-layers
Speed
Experiments with a small test cube
Print accurary in mmm
- 0.6 mm - 5 min
- 0.4 mm - 7 min
- 0.3 mm - 9:27 min
- 0.2 mm - 12:26 min
In the design i printed the accuracy and temperature as text so that the samples will "document themselves ..."